Boosting Supercapacitor Efficiency with Amorphous Biomass-Derived C@TiO2 Composites.

Carbon materials are readily available and are essential in energy storage. One of the routes used to enhance their surface area and activity is the decoration of carbons with semiconductors, such as amorphous TiO2, for application in energy storage devices. This work reports the preparation of amorphous TiO2 nanopowders, which were obtained through the anodization of titanium in ethaline media. The obtained amorphous TiO2 was used to obtain TiO2-decorated carbon (obtained through the carbonization of glycogen precursor from mussel cooking wastewater, under N2 atmosphere) composites through three different methods: electrochemical in-situ attachment of TiO2 nanopowders to the carbon matrix using ultrasounds and sonication in ethaline. Commercial TiO2 was used as the comparison material. Morphology, composition, and structure analysis were performed, followed by the electrochemical analysis in ethaline electrolyte. The in-situ attachment of amorphous TiO2 to the carbon matrix shows the most promising electrochemical performance of 956 F g-1 at 1 A g-1 for the three-electrode cell setup, with 100%  and 98% capacitance retention after 1000 and 10000 cycles. On a two-electrode symmetric solid-state electrolyte cell, the gravimetric capacitance is 1251 F g-1, at 1 A g-1, with 90% and 78% capacitance retention after 1000 and 10000 cycles, respectively.

Oxygen Defects Containing TiN Films for the Hydrogen Evolution Reaction: A Robust Thin-Film Electrocatalyst with Outstanding Performance.

Density functional theory (DFT) calculations of hydrogen adsorption on titanium nitride had previously shown that hydrogen may adsorb on both titanium and nitrogen sites with a moderate adsorption energy. Further, the diffusion barrier was also found to be low. These findings may qualify TiN, a versatile multifunctional material with electronic conductivity, as an electrode material for the hydrogen evolution reaction (HER). This was the main impetus of this study, which aims to experimentally and theoretically investigate the electrocatalytic properties of TiN layers that were processed on a Ti substrate using reactive ion sputtering. The properties are discussed, focusing on the role of oxygen defects introduced during the sputtering process on the HER. Based on DFT calculations, it is shown that these oxygen defects alter the electronic environment of the Ti atoms, which entails a low hydrogen adsorption energy in the range of -0.1 eV; this leads to HER performances that match those of Pt-NPs in acidic media. When a few nanometer-thick layers of Pd-NPs are sputtered on top of the TiN layer, the performance is drastically reduced. This is interpreted in terms of oxygen defects being scavenged by the Pd-NPs near the surface, which is thought to reduce the hydrogen adsorption sites.

Field Emission from Carbon Nanotubes on Titanium Nitride-Coated Planar and 3D-Printed Substrates.

Carbon nanotubes (CNTs) are well known for their outstanding field emission (FE) performance, facilitated by their unique combination of electrical, mechanical, and thermal properties. However, if the substrate of choice is a poor conductor, the electron supply towards the CNTs can be limited, restricting the FE current. Furthermore, ineffective heat dissipation can lead to emitter-substrate bond degradation, shortening the field emitters' lifetime. Herein, temperature-stable titanium nitride (TiN) was deposited by plasma-enhanced atomic layer deposition (PEALD) on different substrate types prior to the CNT growth. A turn-on field reduction of up to 59% was found for the emitters that were generated on TiN-coated bulk substrates instead of on pristine ones. This observation was attributed exclusively to the TiN layer as no significant change in the emitter morphology could be identified. The fabrication route and, consequently, improved FE properties were transferred from bulk substrates to free-standing, electrically insulating nanomembranes. Moreover, 3D-printed, polymeric microstructures were overcoated by atomic layer deposition (ALD) employing its high conformality. The results of our approach by combining ALD with CNT growth could assist the future fabrication of highly efficient field emitters on 3D scaffold structures regardless of the substrate material.

Buccal Mesenchymal Stromal Cells as a Source of Osseointegration of Titanium Implants.

We studied the interaction of human buccal mesenchymal stem cells (MSCs) and osteoblasts differentiated from them with the surface of titanium samples. MSCs were isolated by enzymatic method from buccal fat pads. The obtained cell culture was presented by MSCs, which was confirmed by flow cytometry and differentiation into adipocytes and osteoblasts. Culturing of buccal MSCs on titanium samples was accompanied by an increase in the number of cells for 15 days and the formation of a developed network of F-actin fibers in the cells. The viability of buccal MSCs decreased by 8 days, but was restored by 15 days. Culturing of osteoblasts obtained as a result of buccal MSC differentiation on the surface of titanium samples was accompanied by a decrease in their viability and proliferation. Thus, MSCs from buccal fat pads can be used to coat implants to improve osseointegration during bone reconstruction in craniofacial surgery and dentistry. To improve the integration of osteoblasts, modification of the surface of titanium samples is required.

A review on titanium oxide nanoparticles modified metal-organic frameworks for effective CO2 conversion and efficient wastewater remediation.

Environmental pollution has been increasing since last decade due to increasing industrialisation and urbanisation. Various kinds ofenvironmental pollutants including carbon dioxide (CO2), dyes, pharmaceuticals, phenols, heavy metals along with many organic and inorganic species have been discovered in the various environmental compartments which possess harmful impacts tox human health, wildlife, and ecosystems. Thus, various efforts have been made through regulations, technological advancements, and public awareness campaigns to reduce the impact of the pollution. However, finding suitable alternatives to mitigate their impacts remained a challenge. Metal-organic frameworks (MOFs) are one of the advanced materials with unique features such as high porosity and stability which exhibit versatile applications in environmental remediation. Their composites with titanium oxide nanoparticles (TiO2) have been discovered to offer potential feature such as light harvesting capacity and catalytic activity. The composite integration and properties have been confirmed through characterization using surface area analysis, scanning electron/transmission electron microscopy, atomic force microscopy, fourier transformed infrared spectroscopy, X-ray diffraction analysis, X-ray photoelectron spectroscopy, thermogravimetric analysis, and others. Thus, this work rigorously discussed potential applications of the MOF@TiO2 nanomaterials for the CO2 capture and effective utilization in methanol, ethanol, acetone, acetaldehyde, and other useful products that served as fuel to various industrial processes. Additionally, the work highlights the effective performance of the materials towards photocatalytic degradation of both organic and inorganic pollutants with indepth mechanistic insights. The article will offer significant contribution for the development of sustainable and efficient technologies for the environmental monitoring and pollution mitigation.

In Vitro Inflammatory Cell-Induced Corrosion Using a Lymphocyte and Macrophage Co-Culture.

INTRODUCTION: Cobalt-chromium-molybdenum (CoCrMo) and titanium alloys have been used for orthopaedic implants for decades. However, recent evidence has shown that inflammatory cell-induced corrosion (ICIC) can damage these metal alloys. This study aimed to investigate the mechanisms of ICIC by co-culturing macrophages with lymphocytes. We hypothesized that macrophages would be able to alter the surface oxide layer of CoCrMo and titanium alloy (Ti6Al4V) disks, with greater oxide layer damage occurring in groups with a co-culture compared to a macrophage monoculture and in groups with inflammatory activators compared to nonactivated groups. METHODS: Murine macrophages were cultured on American Society for Testing and Materials (ASTM) F1537 CoCrMo and ASTM F136 Ti6Al4V disks for 30 days and activated with interferon gamma and lipopolysaccharide. Interferon gamma and lipopolysaccharide were added to the culture medium to simulate local inflammation. Macrophages were either cultured alone or in a co-culture with T helper lymphocytes. After the 30-day experiment, scanning electron microscopy was used to examine the disk surfaces, and oxide levels were found using energy dispersive x-ray spectroscopy. RESULTS: Pitting features consistent with previous reports of ICIC were found on disks cultured with cells. Both CoCrMo and Ti6Al4V disks had significantly lower oxide levels in all groups with cells compared to control groups with no cells (P < 0.01). Additionally, CoCrMo disks had significantly lower oxide levels when cultured with activated macrophages and lymphocytes compared to nonactivated macrophages alone (P < 0.001), activated macrophages alone (P < 0.01), and nonactivated macrophages and lymphocytes (P < 0.05). No differences in the oxide levels were found among the Ti6Al4V groups. CONCLUSION: This study demonstrates the ability of macrophages to alter the surface chemistry of commonly used orthopaedic alloys. We found that the addition of lymphocytes and a simulated local inflammatory response may contribute to the ICIC of CoCrMo implants.

In vivo assessment of TiO2 based wear nanoparticles in periprosthetic tissues.

A multimodal approach combining inductively coupled plasma mass spectrometry (ICP-MS), single-particle ICP-MS (spICP-MS), scanning electron microscopy-energy-dispersive X-ray spectroscopy (SEM-EDS) and Raman spectroscopy enabled a deeper insight into the balance between total titanium (Ti), the soluble titanium fraction and titanium dioxide based particle fraction levels in periprosthetic tissues collected from patients undergoing revision surgery. Hydrofluoric acid usage in the sample digestion allowed for complete digestion of TiO2 particles, thus enabling accurate estimation of total Ti levels. The TiO2 fraction represents 38-94% of the titanium load in the six samples where particles were detected, and the fraction is present mainly in samples from patients with aseptically loosened total hip arthroplasty. Further attention was given to this fraction determining the elemental composition, particle count, particle size and modification of TiO2. The spICP-MS analysis confirmed the presence of the TiO2-derived (nano)particles (NPs) with a 39- to 187-nm median size and particle count up to 2.3 × 1011 particles per gram of tissue. On top of that, the SEM-EDS confirmed the presence of the TiO2 nanoparticles with 230-nm median size and an anatase crystal phase was determined by Raman spectroscopy. This study presents a novel multimodal approach for TiO2 particle determination and characterization in tissue samples and is the first in vivo study of this character.

Correlation between the size of released titanium particles and changes in the surface of dental implants during insertion into bone blocks: an in vitro study.

PURPOSE: This study investigated the size and amount of titanium particles immediately released following dental implant insertion into bovine bone blocks and aimed to correlate them with the surface roughness of the implants. METHODS: Twelve bone blocks were prepared from bovine mandibles. Six tapered (group A) and 6 cylindrical (group B) dental implants were inserted into the bone blocks under water irrigation, following the standard drilling protocol. After insertion, the implants were immediately removed from the bone. Scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), and atomic force microscopy were performed to investigate the released titanium particles and implant surface roughness, respectively. The amount of titanium ions in the irrigation water was measured using inductively coupled plasma mass spectrometry. Dynamic light scattering (DLS) was used to determine the size range of the released titanium particles. RESULTS: The percentages of titanium content on the surface of implants decreased in both groups after implantation into bone blocks. SEM-EDX analysis confirmed the presence of titanium particles embedded in the implanted bone bed. Group B implants showed significantly higher concentrations of titanium ions in the collected water than group A implants (0.868 and 0.565 µg/L, respectively). Group A implants demonstrated high pre-implantation surface roughness, which led to a much greater decrease in post-implantation surface roughness than was observed for group B implants. DLS analysis showed that the titanium particles released from group A implants were within the nano-size range, whereas those released from group B implants were within the micro-size range. CONCLUSIONS: Dental implant placement leads to a decrease in implant surface roughness and the immediate release of titanium particles into the peri-implant bone. Variations in the size range and amount of released particles were correlated with implant surface roughness. This finding has clinical implications and warrants additional in vivo studies.

Biomechanical evaluation of various rigid internal fixation modalities for condylar-base-associated multiple mandibular fractures: A finite element analysis.

Condylar-base-associated multiple mandibular fractures are more prevalent than single ones. Direct trauma to mandibular symphysis, body or angle are prone to induce indirect condylar fracture. However, little is known about the effects of various rigid internal fixation modalities in condylar base for relevant multiple mandibular fractures, especially when we are confused in the selection of operative approach. Within the finite element analysis, straight-titanium-plate implanting positions in condylar base contained posterolateral zone (I), anterolateral zone (II), and intermediate zone (III). Von Mises stress (SS) in devices and bone and mandibular displacement (DT) were solved, while maximum values (SSmax and DTmax) were documented. For rigid internal fixation in condylar-base-and-symphysis fractures, I + II modality exhibited least SSmax in screws and cortical bone and least DTmax, I + III modality exhibited least SSmax in plates. For rigid internal fixation in condylar-base-and-contralateral-body fractures, I + III modality exhibited least SSmax in screws and cortical bone, I + II modality exhibited least SSmax in plates and least DTmax. For rigid internal fixation in condylar-base-and-contralateral-angle fractures, I + III modality exhibited least DTmax. The findings suggest that either I + II or I + III modality is a valid guaranty for rigid internal fixation of condylar base fractures concomitant with symphysis, contralateral body or angle fractures.

TiO2-MoS2-PMMA Nanocomposites for an Efficient Water Remediation.

An improvement of water supply and sanitation and better management of water resources, especially in terms of water reuse, is one of the priorities of the European Green Deal. In this context, it is crucial to find new strategies to recycle wastewater efficiently in a low-cost and eco-friendly manner. The immobilization of inorganic nanomaterials on polymeric matrices has been drawing a lot of attention in recent years due to the extraordinary properties characterizing the as-obtained nanocomposites. The hybrid materials, indeed, combine the properties of the polymers, such as flexibility, low cost, mechanical stability, high durability, and ease of availability, with the properties of the inorganic counterpart. In particular, if the inorganic fillers are nanostructured photocatalysts, the materials will be able to utilize the energy delivered by light to catalyze chemical reactions for efficient wastewater treatment. Additionally, with the anchoring of the nanomaterials to the polymers, the dispersion of the nanomaterials in the environment is prevented, thus overcoming one of the main limits that impede the application of nanostructured photocatalysts on a large scale. In this work, we will present nanocomposites made of polymers, i.e., polymethyl methacrylate (PMMA), and photocatalytic semiconductors, i.e., TiO2 nanoparticles (Evonik). MoS2 nanoflakes were also added as co-catalysts to improve the photocatalytic performance of the TiO2. The hybrid materials were prepared using the sonication and solution casting method. The nanocomposites were deeply characterized, and their remarkable photocatalytic abilities were evaluated by the degradation of two common water pollutants: methyl orange and diclofenac. The relevance of the obtained results will be discussed, opening the route for the application of these materials in photocatalysis and especially for novel wastewater remediation.

Efficient Decoupled Electrolytic Water Splitting in Acid through Pseudocapacitive TiO2.

Water electrolysis remains a key component in the societal transition to green energy. Membrane electrolyzers are the state-of-the-art technology for water electrolysis, relying on 80 °C operation in highly alkaline electrolytes, which is undesirable for many of the myriad end-use cases for electrolytic water splitting. Herein, an alternative water electrolysis process, decoupled electrolysis, is described which performed in mild acidic conditions with excellent efficiencies. Decoupled electrolysis sequentially performs the oxygen evolution reaction (OER) and the hydrogen evolution reaction (HER), at the same catalyst. Here, H+ ions generated from the OER are stored through pseudocapacitive (redox) charge storage, and released to drive the HER. Here, decoupled electrolysis is demonstrated using cheap, abundant, TiO2 for the first time. To achieve decoupled acid electrolysis, ultra-small anatase TiO2 particles (4.5 nm diameter) are prepared. These ultra-small TiO2 particles supported on a carbon felt electrode show a highly electrochemical surface area with a capacitance of 375 F g-1. When these electrodes are tested for decoupled water splitting an overall energy efficiency of 52.4% is observed, with excellent stability over 3000 cycles of testing. This technology can provide a viable alternative to membrane electrolyzers-eliminating the need for highly alkaline electrolytes and elevated temperatures.

Ultrathin TiS2@N,S-Doped Carbon Hybrid Nanosheets as Highly Efficient Photoresponsive Antibacterial Agents.

Nanobactericides are employed as a promising class of nanomaterials for eradicating microbial infections, considering the rapid resistance risks of conventional antibiotics. Herein, we present a pioneering approach, reporting the synthesis of two-dimensional titanium disulfide nanosheets coated by nitrogen/sulfur-codoped carbon nanosheets (2D-TiS2@NSCLAA hybrid NSs) using a rapid l-ascorbic acid-assisted sulfurization of Ti3C2Tx-MXene to achieve efficient alternative bactericides. The as-developed materials were systematically characterized using a suite of different spectroscopy and microscopy techniques, in which the X-ray diffraction/Raman spectroscopy/X-ray photoelectron spectroscopy data confirm the existence of TiS2 and C, while the morphological investigation reveals single- to few-layered TiS2 NSs confined by N,S-doped C, suggesting the successful synthesis of the ultrathin hybrid NSs. From in vitro evaluation, the resultant product demonstrates impressive bactericidal potential against both Gram-positive Staphylococcus aureus and Gram-negative Escherichia coli bacteria, achieving a substantial decrease in the bacterial viability under a 1.2 J dose of visible-light irradiation at the lowest concentration of 5 µg·mL-1 compared to Ti3C2Tx (15 µg·mL-1), TiS2-C (10 µg·mL-1), and standard antibiotic ciprofloxacin (15 µg·mL-1), respectively. The enhanced degradation efficiency is attributed to the ultrathin TiS2 NSs encapsulated within heteroatom N,S-doped C, facilitating effective photogenerated charge-carrier separation that generates multiple reactive oxygen species (ROS) and induced physical stress as well as piercing action due to its ultrathin structure, resulting in multimechanistic cytotoxicity and damage to bacterial cells. Furthermore, the obtained results from molecular docking studies conducted via computational simulation (in silico) of the as-synthesized materials against selected proteins (ß-lactamasE. coli/DNA-GyrasE. coli) are well-consistent with the in vitro antibacterial results, providing strong and consistent validation. Thus, this sophisticated study presents a simple and effective synthesis technique for the structural engineering of metal sulfide-based hybrids as functionalized synthetic bactericides.

Anisotropic hydrogel scaffold by flow-induced stereolithography 3D printing technique.

Essential organs, such as the heart and liver, contain a unique porous network that allows oxygen and nutrients to be exchanged, with distinct random to ordered regions displaying varying degrees of strength. A novel technique, referred to here as flow-induced lithography, was developed. This technique generates tunable anisotropic three-dimensional (3D) structures. The ink for this bioprinting technique was made of titanium dioxide nanorods (Ti) and kaolinite nanoclay (KLT) dispersed in a GelMA/PEGDA polymeric suspension. By controlling the flow rate, aligned particle microstructures were achieved in the suspensions. The application of UV light to trigger the polymerization of the photoactive prepolymer freezes the oriented particles in the polymer network. Because the viability test was successful in shearing suspensions containing cells, the flow-induced lithography technique can be used with both acellular scaffolds and cell-laden structures. Fabricated hydrogels show outstanding mechanical properties resembling human tissues, as well as significant cell viability (> 95 %) over one week. As a result of this technique and the introduction of bio-ink, a novel approach has been pioneered for developing anisotropic tissue implants utilizing low-viscosity biomaterials.

Cellulose-based materials in tailoring a novel defective titanium­carbon­phosphorus hybrid composites for highly efficient photocatalytic activity.

Until now, black titania has attracted much interest as a potential photocatalyst. In this contribution, we report the first demonstration of the effective strategy to fundamentally improve the photocatalytic performance using a novel sustainable defective titanium­carbon-phosphorous (TCPH) hybrid nanocomposite. The prepared TCPH was used for photocatalytic degradation of the main organic pollutants, which is methyl orange (MO) dye. The physico-chemical properties of as-prepared samples were characterized by various techniques to observe the transformations after carbonization and the interaction between different composite phases. The existence of Ti+3 and oxygen vacancies at the surface, and a notable increase in surface area, are all demonstrated by TCPH, together with the distinct core-shell structure. These unique properties exhibit excellent photocatalytic performance due to the boosted charge transport and separation. The highest degradation efficiency of methyl orange (MO) was attained in the case of TCPH when compared with titanium-cellulose-phosphorous (TCeP) and titanium­carbon-phosphorous (TCPN). Accordingly, the highest degradation efficiency was achieved by applying the optimal operational conditions of 1 g/L of TCPH catalyst, 10 mg/L of MO, pH of 7 and the temperature at 25 ±â€¯3 °C after 3 min under LED lamp (365 nm) with light intensity 100 mW/cm2. The degradation mechanism was investigated, and the trapping tests showed the dominance of hydroxyl radicals in the degradation of MO. TCPH showed high stability under a long period of operation in five consecutive cycles, which renders the highly promising on an industrial scale. The fabrication of highly active defective titanium­carbon-phosphorous opens new opportunities in various areas, including water splitting, and CO2 reduction.

Clinical effect of chlorhexidine and sodium fluoride on corrosion behavior and surface topography of nitinol orthodontic archwires.

BACKGROUND: Alterations in the mechanical properties of the materials utilized in orthodontic appliances could affect the working properties of the appliances, thereby affecting clinical progress and outcome. Numerous studies have confirmed the correlation between alloy corrosion and raised surface roughness, which has a direct impact on the working characteristics of orthodontic archwires. METHODS: Thirty nickel-titanium (NiTi) orthodontic archwires were utilized in this study. Patients were randomly selected and allocated into three groups according to the randomization plan; (The control group): subjects practiced regular oral hygiene; (The fluoride group): subjects used fluoride for intensive prophylaxis; (The chlorhexidine group): subjects used chlorhexidine. Representative samples were evaluated by SEM, and then SEM images with high resolution were examined using Image J software to determine the surface roughness and obtain the results for further statistical analysis. RESULTS: Our findings indicated a significant difference was found between the three groups regarding the anterior and posterior parts between the control and the two other groups and a non-significant difference between NaF and CHX groups. Overall, the p-value for group comparisons was 0.000 for both parts, indicating a highly significant difference especially between the control and NaF groups. CONCLUSION: Mouthwashes containing sodium fluoride demonstrated more significant surface alterations than the control and CHX groups and should be prescribed in accordance with orthodontic materials to reduce side effects.

Advanced cellulose-based hydrogel TiO2 catalyst composites for efficient photocatalytic degradation of organic dye methylene blue.

Sustainable cellulose-based hydrogels are used in medicine and environmental science. Hydrogels' porosity makes them excellent adsorbents and stable substrates for immobilizing photocatalysts to remove organic dyes. Despite their potential, the implementation of hydrogels for this purpose is still limited due to their high synthesis temperature and low cellulose content. To overcome these challenges, this study develops cellulose-based hydrogels, which have a high cellulose content and can be easily synthesized under ambient conditions. Containing a higher cellulose concentration than previous hydrogels, the synthesized hydrogels are more stable and can be reused numerous times in treatment operations. The hydrogel properties were investigated using Fourier transform infrared spectroscopy, X-ray diffraction and thermal analysis. Scanning electronic microscopy revealed that TiO2 nanoparticles were homogeneously distributed throughout the hydrogel's matrices. In addition, transparent hydrogels allow light to pass through, making them suitable substrates to remove organic dye. The results showed that the hydrogel with TiO2 was able to degrade nearly 90% of organic dye within 180 min. Furthermore, the hydrogel with the embedded catalyst exhibits the potential for reusability with a regeneration efficiency of 80.01% after five runs. These findings suggest that this novel hydrogel is a promising candidate for water pollution remediation.

Exposure to nanoplastics and nanomaterials either single and combined affects the gill-associated microbiome of the Antarctic soft-shelled clam Laternula elliptica.

Nanoplastics and engineering nanomaterials (ENMs) are contaminants of emerging concern (CECs), increasingly being detected in the marine environment and recognized as a potential threat for marine biota at the global level including in polar areas. Few studies have assessed the impact of these anthropogenic nanoparticles in the microbiome of marine invertebrates, however combined exposure resembling natural scenarios has been overlooked. The present study aimed to evaluate the single and combined effects of polystyrene nanoparticles (PS NP) as proxy for nanoplastics and nanoscale titanium dioxide (nano-TiO2) on the prokaryotic communities associated with the gill tissue of the Antarctic soft-shell clam Laternula elliptica, a keystone species of marine benthos Wild-caught specimens were exposed to two environmentally relevant concentrations of carboxylated PS NP (PS-COOH NP, ∼62 nm size) and nano-TiO2 (Aeroxide P25, ∼25 nm) as 5 and 50 µg/L either single and combined for 96h in a semi-static condition.Our findings show a shift in microbiome composition in gills of soft-shell clams exposed to PS NP and nano-TiO2 either alone and in combination with a decrease in the relative abundance of OTU1 (Spirochaetaceae). In addition, an increase of gammaproteobacterial OTUs affiliated to MBAE14 and Methylophagaceae (involved in ammonia denitrification and associated with low-quality water), and the OTU Colwellia rossensis (previously recorded in polluted waters) was observed. Our results suggest that nanoplastics and nano-TiO2 alone and in combination induce alterations in microbiome composition by promoting the increase of negative taxa over beneficial ones in the gills of the Antarctic soft-shell clam. An increase of two low abundance OTUs in PS-COOH NPs exposed clams was also observed. A predicted gene function analysis revealed that sugar, lipid, protein and DNA metabolism were the main functions affected by either PS-COOH NP and nano-TiO2 exposure. The molecular functions involved in the altered affiliated OTUs are novel for nano-CEC exposures.

Hydroxide-derived Nanostructures: Scalable Synthesis, Characterization, Properties and Potential Applications.

Metal oxide nanostructures have received an increasing attention owing to their unique chemical and physical properties along with their widespread applications in various fields. In this article, we provide an overview of our recent discovery - christened Hydroxides-Derived Nanostructures, or HDNs - in which we react hydroxide aqueous solutions (mostly tetramethylammonium hydroxide, TMAH) at temperatures < 100 °C and under atmospheric pressure with various metal-containing precursors to scalably prepare novel metal oxide nanostructures. In one case, we converted a dozen commercial and earth abundant Ti-containing powders such as binary carbides, nitrides, borides, among others, into new, one-dimensional TiO2-based lepidocrocite (1DL) nanofilaments (NFs). Application-wise, 1DLs show outstanding performance in a number of energy, environmental, and biomedical fields such as photo- and electrocatalysis, water splitting, lithium-sulfur and lithium-ion batteries, water purification, dye degradation, cancer therapy, and polymer composites. In addition to 1DL, the HDNs family encompasses other metal oxides nanostructures including magnetic Fe3O4 nanoparticles and MnO2 birnessite-based crystalline two-dimensional (2D) flakes. The latter showed promise as a bifunctional electrocatalyst for water oxidation and oxygen reduction, as well as cathodes in aqueous asymmetric supercapacitor and in an aqueous ammonium ion battery. Our developed recipe provides a new vista in the molecular self-assembly synthesis of metal oxide nanomaterials that can advance the field with a library of novel nanostructures with substantial implications in a multitude of fields. This article is protected by copyright. All rights reserved.

Synthesis, in vitro antitumor evaluation and structure activity relationship of heptacoordinated amino-bis(Phenolato) Ti(IV) complexes stabilized by 2,6-dipicolinic acid.

Eighteen novel Ti(IV) complexes stabilized by different chelating amino-bis(phenolato) (ONNO, ONON, ONOO) ligands and 2,6-dipicolinic acid as a second chelator were synthesized with isolated yields ranging from 79 to 93%. Complexes were characterized by 1H and 13C-NMR spectroscopy, as well as by HRMS and X-Ray diffraction analysis. The good to excellent aqueous stability of these Ti(IV) complexes can be modulated by the substitutions on the 2-position of the phenolato ligands. Most of the synthesized Ti(IV) complexes demonstrated potent inhibitory activity against Hela S3 and Hep G2 tumor cells. Among them, the naphthalenyl based Salan type 2j, 2-picolylamine based [ONON] type 2n and N-(2-hydroxyethyl) based [ONOO] type 2p demonstrated up to 40 folds enhanced cytotoxicity compared to cisplatin together with a significantly reduced activity against healthy AML12 cells. The three Ti(IV) complexes exhibited fast cellular uptake by Hela S3 cells and induced almost exclusively apoptosis. 2j could trigger higher level of ROS generation than 2p and 2n.

Inorganic UV filter-based sunscreens labelled as eco-friendly threaten sea urchin populations.

Although the negative effects of inorganic UV filters have been documented on several marine organisms, sunscreen products containing such filters are available in the market and proposed as eco-friendly substitutes for harmful, and already banned, organic UV filters (e.g. octinoxate and oxybenzone). In the present study, we investigated the effects of four sunscreen products, labelled by cosmetic companies as "eco-friendly", on the early developmental stages of the sea urchin Paracentrotus lividus, a keystone species occurring in vulnerable coastal habitats. Among sunscreens tested, those containing ZnO and TiO2 or their mix caused severe impacts on sea urchin embryos. We show that inorganic UV filters were incorporated by larvae during their development and, despite the activation of defence strategies (e.g. phagocytosis by coelomocytes), generated anomalies such as skeletal malformations and tissue necrosis. Conversely, the sunscreen product containing only new-generation organic UV filters (e.g. methylene bis-benzotriazolyl tetramethyl, ethylhexyl triazone, butylphenol diethylamino hydroxybenzoyl hexyl benzoate) did not affect sea urchins, thus resulting actually eco-compatible. Our findings expand information on the impact of inorganic UV filters on marine life, corroborate the need to improve the eco-friendliness assessment of sunscreen products and warn of the risk of bioaccumulation and potential biomagnification of inorganic UV filters along the marine food chain.